MB27L2 - 27mm Loud Intermittent Buzzer 1.5V to 15V DC A buzzer is a small yet efficient component to add sound features to our project/system. It is a very small and compact 2-pin structure hence can be easily used on breadboard, Perf Board and even on PCBs which makes this a widely used component in most electronic applications. There are two types of buzzers that are commonly available. The one shown here is a simple buzzer that when powered will make a Beep Beep Beep. Sound due to the internal oscillating circuit present inside it. But, the one shown here is most widely used because it can be customized with the help of other circuits to fit easily in our application. Applications: Electrical alarms Educational purposes Security applications Electronic Metronomes Household applications Also check the MB35L2 - 35mm Loud Intermittent Buzzer from Iotcart. The buzzer operates within a voltage range of 1.5 to 15V DC, with good frequency response.

MB27M - Maruti 27mm Musical Buzzer 5V to 15V DC A buzzer is a small yet efficient component to add sound features to our project/system. It is a very small and compact 2-pin structure hence can be easily used on breadboards, Perf Board and even on PCBs which makes this a widely used component in most electronic applications. There are two types of buzzers that are commonly available. The one shown here is a simple buzzer which when powered will give a musical tone. Sound due to the internal oscillating circuit present inside it. But, the one shown here is most widely used because it can be customized with the help of other circuits to fit easily in our application. It is mountable via screws on the side to any surface. It has low current consumption and has flange-type mounting. Applications: Electrical alarms Educational purposes Security applications Electronic Metronomes Household applications

MB35L - 35mm Loud Continuous Buzzer This is a DC 1.5-15V Active buzzer. It comes with 2 Pin terminals. This buzzer is a small yet efficient component to add sound features to our project/system. It is very small and compact 2-pin structure hence can be easily used on breadboard, Perf Board and even on PCBs which makes this a widely used component in most electronic applications. There are two types of buzzers that are commonly available. The one shown here is a simple buzzer which when powered will make a Continuous Beep. Sound due to the internal oscillating circuit present inside it. But, the one shown here is most widely used because it can be customized with help of other circuits to fit easily in our application. Applications: Electrical alarms Educational purposes Security applications Electronic Metronomes Household applications

MB35L - 35mm Loud Continuous Buzzer 1.5V to 15V DC A buzzer is a small yet efficient component to add sound features to our project/system. It is a very small and compact 2-pin structure hence can be easily used on breadboards, Perf Board and even on PCBs which makes this a widely used component in most electronic applications. There are two types of buzzers that are commonly available. The one shown here is a simple buzzer which when powered will make a Continuous Beep. Sound due to the internal oscillating circuit present inside it. But, the one shown here is most widely used because it can be customized with the help of other circuits to fit easily in our application. Applications: Electrical alarms Educational purposes Security applications Electronic Metronomes Household applications

MB35M - 35mm Musical Buzzer An audio signaling device like a beeper or buzzer may be electromechanical or piezoelectric or mechanical type. The main function of this is to convert the signal from audio to sound. Generally, it is powered through DC voltage and used in timers, alarm devices, printers, alarms, computers, etc. Based on the various designs, it can generate different sounds like alarm, music, bell & siren. Applications: Electrical alarms Educational purposes Security applications Electronic Metronomes Household applications Communication Devices

MC-38 Wired Magnetic House Security Alarm Sensor for Door and Windows MC-38 Wired Door Window Sensor Magnetic Switch Home Alarm System can be used as a door or window security system. It produces the signal when moved away from each other which can be fed to the microcontroller to perform the desired action as per requirement. This sensor is suitable to use for triggering an alarm or ON/OFF light inside a cupboard sliding door. This wired sensor is triggered by the magnet. When the magnet is closed by, the circuit is closed or open if the magnet is far from the sensor. This MC-38 Magnetic Contact Switch Sensor acts like a normal switch so, you can connect to the Ground(GND) pin too. Not necessarily connect to power supply. Note : Normally closed: When the magnet is together, the circuit is conductive( light on); when the magnet is separate, the circuit is not conductive ( light off ). For example: Install on the door, close door light on. open door light off. Applications: Doors Windows Sliding cupboards Home Security Projects

MCP2515 Can Bus Module Board Controlled Area Network of simple CAN is a bus standard that allows a Microcontroller and its peripheral devices to communicate without the need of a host device or a computer. The MCP2515 CAN bus module is designed with an SPI 51 Single Chip Program and features a TJA1050 Receiver. It is created to control a CAN Bus device by SPI interface with your MCU. It is best used by microcontrollers and boards compatible with Arduino like UNO boards. The MCP2515 CAN Bus Controller is a simple Module that supports CAN Protocol version 2.0B and can be used for communication at 1Mbps. In order to set up a complete communication system, you will need two CAN Bus modules. The MCP2515 CAN bus module consists of standard frames, extended frames, and remote frames. You can use the serial port of the  MCP2515 CAN bus module to view communication data as well. Pin Details VCC :5V power input pin GND : power ground pin CS : SPI SLAVE select pin (Active low) SO : SPI master input slave output lead SI : SPI master output slave input lead SCLK: SPI clock pin INT: MCP2515 interrupt pin Pin Diagram: Pin Diagram of MCP2515 Can Bus Module Board Applications: Electronic Gear Shift System Automobiles Main Interface in Automation (like industrial) Medical Equipment Robotics Auto Start/Stop of Car Engine

MCP4725 I2C DAC Breakout Module MCP4725 I2C DAC Breakout Development Board Module has MCP4725 which is an I2C controlled Digital-to-Analog converter (DAC). A very cost-efficient option of DAC allows you to send an analog signal, such as a sine wave, from a digital source, such as the I 2 C interface on the Arduino microcontroller. Digital to analog converters are great for sound generation, musical instruments, and many other creative projects!

ME-8108 Rotary Adjustable Roller Lever Arm AC Limit Switch for CNC Machines ME-8108 Rotary Adjustable Roller Lever Arm Mini Limit Switch also named the POSITION SWITCH, is a commonly used small current main electrical appliances, the contact action is realized through the collision of the moving parts of the production machinery or segmented control circuit, achieving a particular control target.  Most popular use is a limit switch for DIY CNC mills. The lever arm can be rotated to the left by 90° degree and to the right by 90° degree. Perfect for electrical control switches in mechanical and other industries; This Limit Switch can be widely used in various machines to monitor the position of moving parts of machines and plants; Please pay attention to the Voltage Rating and check with the voltage of your place to make sure the Limit Switch successfully works. Features: Adjustable Roller Lever Arm: The lever arm can be rotated 90 degrees to the left or right, providing flexibility in installation. High Durability: Rated for 300,000 electrical cycles and 10,000,000 mechanical cycles. Wide Voltage Range: Can handle up to 250V AC and 115V DC. Momentary Actuator Action: The switch operates momentarily when the lever arm is actuated. Dustproof and Water Resistant: Features IP65 ingress protection, making it suitable for harsh environments. Versatile Applications: Commonly used in production lines, robotics, CNC machines, and IoT projects. Applications: Production Lines: Used to monitor and control the position of moving parts in automated production lines. Robotics: Helps in detecting the position and movement of robotic arms and other components. CNC Machines: Ensures precise positioning and movement control in CNC drilling and milling machines. IoT Projects: Integrated into IoT systems for monitoring and controlling various mechanical processes. Safety Mechanisms: Acts as a safety switch to prevent machinery from operating outside of set parameters. Home Automation: Used in smart home devices to detect the position of doors, windows, and other moving parts.

Me-95+ Mario 60W Hot Melt Glue Gun The Me-95+ Mario 60W Hot Melt Glue Gun heats up quickly in 3-5 minutes and is made with durable, heat-resistant plastic. It has a built-in fuse to prevent overheating and damage. The gun saves 50% of electricity with its efficient and constant temperature, making it energy-saving. It is designed for long-lasting use, providing a reliable solution for all your gluing needs.