3D printer parts heating-controller MKS MOS25 V1.0 for heat bed extruder MOS module support big current 25A This is a Heated Bed controller that can control the temperature of any 12V/24V heated bed with a maximum current rating of 25A. Very powerful to withstand higher current than normal ramps or other 3D printer driver. A general add-on heated bed power expansion module for 3D printer Completely solve the hot bed power is too large and the load current issue.  Wiring Diagram: Wiring diagram of MKS MOS25 V1.0 with heatbed and board. Note: This module under the premise of normal cooling, found at I (Max) = 25A stable work situation, the process of using the current not exceed 25A Package Includes: 1 x 3D printer parts heating-controller MKS MOS25 V1.0 for heat bed extruder MOS module support big current 25A Specifications: Model MKS MOS25 Operating Voltage 12/24V Max. Current 25A Max. Power 300W Compatible RepRap, Creality CR-10, Anet E10, etc. Dimensions 60 x 50 x 40mm Weight 35g

MK2A PCB Aluminium Heatbed This heatbed for 3D printers is of the model MK2A and is aluminium manufactured PCB. It is an overall black coloured aluminium heatbed and has a thickness of 3mm. The power input needed for the 3D printer heatbed is 12V 200W/24V 240W. This high-quality aluminium Plate PCB Heat Bed is compatible for MK2A 3D printer, MK2B and MK3. The PCB Heat bed comes along with a 60 cm cable and LED Thermistors. Heat beds are used because they dramatically improve print quality by keeping the extruded plastic warm and thus preventing warping. Package Includes: 1 x MK2A PCB Aluminium Heatbed Features of the MK2A Aluminium Heatbed Model MK2A Heatbed Material Aluminium Size 300 x 200 mm Thickness 3mmThe Mk2A  Colour Black on both sides Power Input 12V 200W/24V 240W Compatibility MK2A 3D printer, MK2B and MK3

Ultrabase 200*200mm 3D Printer Platform Tempered Heated Bed Glass Plate with Microporous Coating This is a high-quality sticker with adhesive backing for the 3d printer builds plates of dimensions 200mm x 200mm. Ultrabase Glass Plate helps you to avoid warping and offers a flat surface. Ultrabase 3D Printer glass plate works perfectly with Creality3D printers in the 200mm size. It helps you to avoid warping and enables you to perform 3D prints with flat surfaces. Ultrabase helps to prevent following problems: Filament doesn’t stick onto the platform due to flatness of aluminium bed Ultrabase is an alternative to use blue tape or glue to make 3D prints stick to the platform and minimize warping It makes objects more easy to remove. Often 3D printed parts are not easy to remove or you are afraid to remove them from the building bet. Ultrabase stops this worries. You don’t want to chance your masking tape after each 3D print. If you don’t change it it may be damaged and your object will not stick on the surface. Ultrabase is your solution! Temperature settings for different filaments: PLA: 50-70ºC Flexible filament: 50-70ºC ABS: 100-125ºC ( 110ºCis recommended ) PC: 100-130ºC ( 120ºC is recommended ) Nelon: 90-120ºC ( 110ºC is recommended ) PP: 100-130ºC ( 120 ºC is recommended ) PETG: 50-70ºC Note:  Suggested bed temperature may vary depending on the filament material. Please properly level the bed before printing Never let the nozzle rub against the Ultrabase directly Clean the platform surface with alcohol/water. check out : Ultrabase 310*310mm 3D Printer Platform Tempered Heated Bed Glass Plate with Microporous Coating Package Includes: 1 x Ultrabase 200*200mm 3D Printer Build Surface Heatbed Sticker for 3D Printer Heated Bed Specifications: Material  Tempered glass with microporous inorganic coating Heat Bed Power 140-145W Item size (mm) 200x 200(L x B) Weight 550g

3D Printer Parts Spring For Heated bed MK3 CR-10 Hotbed (Blue) This is an imported spring for the heat bed of an MK3 3D printer. This spring gives good stiffness to the bed of the 3D printer and doesn’t allow the printer bed to shift during the print. This is essential while printing a 3D print with a larger print time because if the bed is shifted during the print there are huge chances of the print being spoiled. These springs are robust helical compression springs consisting of rectangular wire, commonly used with die sets. Rectangular wire is employed to reduce the solid height and increase the space efficiency of the design. Package Includes: 1 x 3D Printer Parts Spring For Heated bed MK3 CR-10 Hotbed Specifications: Color Blue Material Metal Length (mm) 25 Width (mm) 10 Weight 10g

RAMPS 1.4 Shield for 3D Printer The RepRap Arduino-compatible MEGA Pololu Shield, or RAMPS for short. It is designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino-compatible Mega with the powerful Arduino-compatible MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino-compatible MEGA shield for easy service, part replacement, upgrade-ability and expansion. Additionally, a number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack. Package Includes: 1 x 3D Printer Ramps 1.4 Shield Specifications Model  RAMPS 1.4 Shield  Dimensions  5 x 4 x 3cms  Weight  15 grams

RepRap MK2B 3D printers Dual Power PCB HeatBed With 14AWG Cable (Red) A heatbed improves printing quality by helping to prevent warping. As extruded plastic cools, it shrinks slightly. When this shrinking process does not occur throughout a printed part evenly, the result is a warped part.  This warping is commonly seen as corners being lifted off of the build platform. Printing on a heated bed allows the printed part to stay warm during the printing process and allow more even shrinking of the plastic as it cools below melting point. Heated beds usually yield higher quality finished builds with materials such as ABS and PLA. A heatbed can also allow users to print without rafts. This self-regulating heat bed provide a temperature controlled build platform ideally suited for printing with PLA or ABS. check out : 1.75mm Dark Blue ABS Filament -1Kg Connection: 12V connection: One cable connected to 1, another cable connected to a wire 2, 3 at the same time. At this time the resistance value of the two lines is 1.0 ~ 1.2, the actual power is 144W. 24V connection: One cable connection 2, another line connected to 3 (1 unconnected), the resistance value of the two lines is 4.0, actual power is 24 * 24/4 = 144W. The new version of the circuit, whether connected 12V or 24V, the power will stable at 144W. Test Report: 12V connection: Current is 9.8A, as the temperature increases, the current drops to 8.8A (physical tips: resistance becomes larger as the temperature rises) 24V connection: The theoretical maximum current is less than 5A.

MKS TFT-WIFI V1.0 ESP8266 WIFI Module  This Wifi module is created and developed by Makerbase team, It is capable of high transmission rate and stability . It is compatible greatly with MKS TFT24, MKS TFT28, MKS TFT32 display screen. It supports document transfer  via APP, and Cloud printing and firmware upgrading. How to Download APP for MKS TFT-WIFI V1.0? Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.  Package Includes: 1 x MKS TFT-WIFI V1.0 APP Wireless Router ESP8266 WIFI Module Remote Control for MKS TFT Touch Screen Specifications: Configuration Cloud servers, Android/IOS APP Firmware Upgrade Via SD or WEB Transfer Rate 80~100Kbytes Operating Voltage 3.3 VDC Protocol TCP/IP Dimensions 25 x 23mm

3D Printer Parts Spring For Heated bed MK3 CR-10 Hotbed (Yellow) This is an imported spring for the heat bed of an MK3 3D printer. This spring gives good stiffness to the bed of the 3D printer and doesn’t allow the printer bed to shift during the print. This is essential while printing a 3D print with a larger print time because if the bed is shifted during the print there are huge chances of the print being spoiled. These springs are robust helical compression springs consisting of rectangular wire, commonly used with die sets. Rectangular wire is employed to reduce the solid height and increase the space efficiency of the design. Check out our entire range of Heat Bed & Controller Package Includes: 1 x 3D Printer Parts Spring For Heated bed MK3 CR-10 Hotbed Specifications: Color Yellow Material Metal Length (mm) 25 Width (mm) 10 Weight 10g

12V 0.18A CPU Cooling Fan DC cooling fan fans blow air along the axis of the fan or parallel to the track of the blade axis. Dc axial fans are found in a variety of applications, including computing, servers, telecommunication cabinets, and any type of equipment where the need for thermal control is necessary for the improved reliability and life extension of the components that are included in the system.  Specifically designed for pressure demanding applications such as CPU or radiator cooling. It has high precision bearing, long life and low noise. Applications: Can be used in CPU cooling Can be used in Incubators Can be used in 3D Printers Accessories PACKAGE INCLUDES: 1 x 12V 0.18A CPU Cooling Fan SPECIFICATIONS Voltage Supply  12V Connector  Connector 2 Pin Material  Plastic  Dimensions  80 x 80mm Weight  25 grams

Ultrabase 310*310mm 3D Printer Platform Tempered Heated Bed Glass Plate with Microporous Coating This is a high-quality sticker with adhesive backing for the 3d printer builds plates of dimension 310mm x 310mm. Ultrabase Glass Plate helps you to avoid warping and offers a flat surface. Ultrabase 3D Printer glass plate works perfectly with Creality3D printers in the 310mm size. It helps you to avoid warping and enables you to perform 3D prints with flat surfaces. Ultrabase helps to prevent following problems: Filament doesn’t stick onto the platform due to flatness of aluminium bed Ultrabase is an alternative to use blue tape or glue to make 3D prints stick to the platform and minimize warping It makes objects more easy to remove. Often 3D printed parts are not easy to remove or you are afraid to remove them from the building bet. Ultrabase stops this worries. You don’t want to chance your masking tape after each 3D print. If you don’t change it it may be damaged and your object will not stick on the surface. Ultrabase is your solution! check out : Ultrabase 300*300mm 3D Printer Platform Tempered Heated Bed Glass Plate with Microporous Coating Temperature settings for different filaments: PLA:50-70ºC Flexible filament: 50-70ºC ABS:100-125ºC ( 110ºCis recommended ) PC:100-130ºC ( 120ºC is recommended ) Nelon:90-120ºC ( 110ºC is recommended ) PP:100-130ºC ( 120 ºC is recommended ) PETG: 50-70ºC Note:  Suggested bed temperature may vary depending on the filament material. Please properly level the bed before printing Never let the nozzle rub against the Ultrabase directly Clean the platform surface with alcohol/water. Package Includes: 1 x Ultrabase 310*310mm 3D Printer Build Surface Heatbed Sticker for 3D Printer Heated Bed Specifications: Material  Tempered glass with microporous inorganic coating Heat Bed Power 140-145W Item size (mm) 310x 310(L x B) Weight 800g

Ultrabase 235*235mm 3D Printer Platform Tempered Heated Bed Glass Plate with Microporous Coating This is a high-quality sticker with adhesive backing for the 3d printer builds plates of dimension 235mm x 235mm. Ultrabase Glass Plate helps you to avoid warping and offers a flat surface. Ultrabase 3D Printer glass plate works perfectly with Creality3D printers in the 235mm size. It helps you to avoid warping and enables you to perform 3D prints with flat surfaces. Ultrabase helps to prevent following problems: Filament doesn’t stick onto the platform due to flatness of aluminium bed Ultrabase is an alternative to use blue tape or glue to make 3D prints stick to the platform and minimize warping It makes objects more easy to remove. Often 3D printed parts are not easy to remove or you are afraid to remove them from the building bet. Ultrabase stops this worries. You don’t want to chance your masking tape after each 3D print. If you don’t change it it may be damaged and your object will not stick on the surface. Ultrabase is your solution! Temperature settings for different filaments: PLA:50-70ºC Flexible filament: 50-70ºC ABS:100-125ºC ( 110ºCis recommended ) PC:100-130ºC ( 120ºC is recommended ) Nelon:90-120ºC ( 110ºC is recommended ) PP:100-130ºC ( 120 ºC is recommended ) PETG: 50-70ºC Note:  Suggested bed temperature may vary depending on the filament material. Please properly level the bed before printing Never let the nozzle rub against the Ultrabase directly Clean the platform surface with alcohol/water. Package Includes: 1 x Ultrabase 235*235mm 3D Printer Build Surface Heatbed Sticker for 3D Printer Heated Bed Specifications: Material  Tempered glass with microporous inorganic coating Heat Bed Power 140-145W Item size (mm) 235x 235(L x B) Weight 700g

Ultrabase 214*214mm 3D Printer Platform Tempered Heated Bed Glass Plate with Microporous Coating This is a high-quality sticker with adhesive backing for the 3d printer builds plates of dimension 214mm x 214mm. Ultrabase Glass Plate helps you to avoid warping and offers a flat surface. Ultrabase 3D Printer glass plate works perfectly with Creality3D printers in the 214mm size. It helps you to avoid warping and enables you to perform 3D prints with flat surfaces. Ultrabase helps to prevent following problems: Filament doesn’t stick onto the platform due to flatness of aluminium bed Ultrabase is an alternative to use blue tape or glue to make 3D prints stick to the platform and minimize warping It makes objects more easy to remove. Often 3D printed parts are not easy to remove or you are afraid to remove them from the building bet. Ultrabase stops this worries. You don’t want to chance your masking tape after each 3D print. If you don’t change it it may be damaged and your object will not stick on the surface. Ultrabase is your solution! Temperature settings for different filaments: PLA:50-70ºC Flexible filament: 50-70ºC ABS:100-125ºC ( 110ºCis recommended ) PC:100-130ºC ( 120ºC is recommended ) Nelon:90-120ºC ( 110ºC is recommended ) PP:100-130ºC ( 120 ºC is recommended ) PETG: 50-70ºC Note:  Suggested bed temperature may vary depending on the filament material. Please properly level the bed before printing Never let the nozzle rub against the Ultrabase directly Clean the platform surface with alcohol/water. Package Includes: 1 x Ultrabase 214x214mm 3D Printer Build Surface Heatbed Sticker for 3D Printer Heated Bed Specifications: Material  Tempered glass with microporous inorganic coating Heat Bed Power 140-145W Item size (mm) 214 x 214 (L x B) Weight 600g

Ultrabase 220*220mm 3D Printer Platform Tempered Heated Bed Glass Plate with Microporous Coating This is a high-quality sticker with adhesive backing for the 3d printer builds plates of dimensions 220mm x 220mm. Ultrabase Glass Plate helps you to avoid warping and offers a flat surface. Ultrabase 3D Printer glass plate works perfectly with Creality3D printers in the 220mm size. It helps you to avoid warping and enables you to perform 3D prints with flat surfaces. Ultrabase helps to prevent following problems: Filament doesn’t stick onto the platform due to flatness of aluminium bed Ultrabase is an alternative to use blue tape or glue to make 3D prints stick to the platform and minimize warping It makes objects more easy to remove. Often 3D printed parts are not easy to remove or you are afraid to remove them from the building bet. Ultrabase stops this worries. You don’t want to chance your masking tape after each 3D print. If you don’t change it it may be damaged and your object will not stick on the surface. Ultrabase is your solution! Temperature settings for different filaments: PLA: 50-70ºC Flexible filament: 50-70ºC ABS: 100-125ºC ( 110ºCis recommended ) PC: 100-130ºC ( 120ºC is recommended ) Nelon: 90-120ºC ( 110ºC is recommended ) PP: 100-130ºC ( 120 ºC is recommended ) PETG: 50-70ºC Note:  Suggested bed temperature may vary depending on the filament material. Please properly level the bed before printing Never let the nozzle rub against the Ultrabase directly Clean the platform surface with alcohol/water. Package Includes: 1 x Ultrabase 220*220mm 3D Printer Build Surface Heatbed Sticker for 3D Printer Heated Bed Specifications: Material  Tempered glass with microporous inorganic coating Heat Bed Power 140-145W Item size (mm) 220x 220(L x B) Weight 600g

Ultrabase 300*300mm  3D Printer Platform Tempered Heated Bed Glass Plate with Microporous Coating This is a high-quality sticker with adhesive backing for the 3d printer builds plates of dimensions 300mm x 300mm. Ultrabase Glass Plate helps you to avoid warping and offers a flat surface. Ultrabase 3D Printer glass plate works perfectly with Creality3D printers in the 300mm size. It helps you to avoid warping and enables you to perform 3D prints with flat surfaces. Ultrabase helps to prevent following problems: Filament doesn’t stick onto the platform due to flatness of aluminium bed Ultrabase is an alternative to use blue tape or glue to make 3D prints stick to the platform and minimize warping It makes objects more easy to remove. Often 3D printed parts are not easy to remove or you are afraid to remove them from the building bet. Ultrabase stops this worries. You don’t want to chance your masking tape after each 3D print. If you don’t change it it may be damaged and your object will not stick on the surface. Ultrabase is your solution! check out : Ultrabase 235*235mm 3D Printer Platform Tempered Heated Bed Glass Plate with Microporous Coating Temperature settings for different filaments: PLA: 50-70ºC Flexible filament: 50-70ºC ABS: 100-125ºC ( 110ºCis recommended ) PC: 100-130ºC ( 120ºC is recommended ) Nelon: 90-120ºC ( 110ºC is recommended ) PP: 100-130ºC ( 120 ºC is recommended ) PETG: 50-70ºC Note:  Suggested bed temperature may vary depending on the filament material. Please properly level the bed before printing Never let the nozzle rub against the Ultrabase directly Clean the platform surface with alcohol/water. check out : Ultrabase 200*200mm 3D Printer Platform Tempered Heated Bed Glass Plate with Microporous Coating Package Includes: 1 x Ultrabase 300*300mm 3D Printer Build Surface Heatbed Sticker for 3D Printer Heated Bed Specifications: Material  Tempered glass with microporous inorganic coating Heat Bed Power 140-145W Item size (mm) 300x 300(L x B) Weight 780g

3D Printer Power Controller Module for Heated Bed The 3D printer power controller module is a power expansion board that features a one of a kind snow flak heat sink design for the best heat dissipation possible. This power controller module for 3D printers is designed based on  power mosfet and can be used in both lerdge motherboard and other 3d printer motherboards.