10K Pot potentiometer with Knob A 10K Pot potentiometer is a type of variable resistor that is commonly used in electronic circuits. It has a resistance value of 10,000 Ohms, which is indicated by the "10K" in its name. A potentiometer with a knob is a type of manual control that allows you to adjust the resistance of the potentiometer by turning the knob. This is useful for adjusting the level of a signal or the resistance in a circuit. The knob is typically marked with a scale or tick marks to indicate the position of the resistance. Package Includes: 1 x 10K Pot potentiometer with Knob Specifications: Resistance 10K Output signal Analog signal Operating Voltage +5V DC Dimensions 18x23x25mm Weight 8g

22k Potentiometer (10 pcs) The 22K Pot Potentiometer is a three-terminal variable resistor that is used to vary or change the resistance. It is normally used to control any device. The 22K Potentiometer is used for adjusting various parameters like voltage, current, etc in an electronic circuit. The 22 POT Potentiometer is a passive electronic component that has two end terminals with a resistive element and the sliding contact called the wiper acts as the third terminal. It is mostly used in applications where a single turn can provide enough control resolution.

10K Pot Potentiometer - (Pack of 5) The 10K Pot Potentiometer is a three-terminal variable resistor that is used to vary or change the resistance. It is normally used to control any device. The 10K Potentiometer is used for adjusting various parameters like voltage, current, etc in an electronic circuit. The POT Potentiometer is a passive electronic component that has two end terminals with a resistive element and the sliding contact called the wiper acts as the third terminal. It is mostly used in applications where a single turn can provide enough control resolution. Applications of 10K PoTPotentiometer: DIY kits. Major projects. Mini projects. Audio control. Television control. Motion control. Computation. What are Potentiometers? A potentiometer is a three-terminal resistor with a sliding or rotating contact that forms an adjustable voltage divider. Package Includes: 5 x 10K Pot Potentiometer Specifications: Resistance  10K Ohm  Potentiometer Type  Pot Potentiometer  Material Carbon Film and Metal Interface 3 Pin Shaft Length 15mm Dimensions  1 x 1 x 1cms  Weight  15 grams

Digital Potentiometer Board Module This is a X9C103S DC 3-5V Digital Potentiometer Board Module for Arduino. The X9C103 is a digitally controlled (XDCP) potentiometer. It consists of a resistor array, wiper switch, control section and non-volatile memory. Wiper position is controlled via a 3-wire interface. The potentiometer is implemented by a resistor array consisting of 99 resistive elements and a wiper switching network. Between each element and at each end there are tap points that can be accessed for wiper connections. The wiper element position is controlled by the CS, U/D, and INC inputs. The wiper position can be saved in non-volatile memory and recalled on subsequent power ups. DC3V-5V X9c103S digital potentiometer has his three sections: Input control, counter and decoding section. non-volatile memory; and resistor arrays. The input control section works exactly like an up/down counter. The output of this counter is decoded to turn on a single electronic switch that connects a point on the register array to the wiper output. Under proper conditions, the contents of the counter can be saved in non-volatile memory and saved for future use. The resistor array consists of 99 individual resistors connected in series. Between the ends of the array and each resistor there is an electronic switch that transfers the potential at that point to the wiper.The wiper behaves like a mechanical equivalent at one of the fixed terminals and does not move beyond its final position. This means that the counter will not jump when clocked to either extreme. The device's electronic switches operate in a make-before-break mode as the wiper changes tap positions. When the wiper moves to multiple positions, multiple taps are connected to the wiper during tIW (INC to VW/RW switching). Moving the wiper to multiple positions can temporarily significantly reduce the overall value of the device. When the unit is turned off, the last saved wiper position is retained in non-volatile memory. When power returns, the memory contents are recalled and the wipers are reset to their last saved values. An internal charge pump allows a wide voltage range (-5V to 5V) to be applied to his XDCP pin while maintaining the convenience of a single supply. A typical charge pump noise of 20 mV at 850 kHz should be considered when designing the application circuit. The digital potentiometer module is accompanied by a test program. The program code is C language code and is written in sub-modules. The code includes: main function, display sub-function, button sub-function and header file of each module. You can use KEIL4 to open the source code for testing and learning. The digital potentiometer VL and ports correspond to the low and high end of the sliding rheostat, respectively, allowing the input voltage range from -5V to +5V.

47K ohm 16mm Rotatory Variable Potentiometer Potentiometers are very useful in changing the electrical parameters of a system. It is a single turn 47K Potentiometer with a rotating knob. These potentiometers are also commonly called as a rotary potentiometer or just POT in short.  A potentiometer knob can also be used along with this POT for aesthetic purposes. This is a carbon track, single turn, adjustable resistances, of value 47KOhm Knob potentiometer. It is meant for mounting on panel and is supplied complete with a knob. The knob is affixed on the plastic spindle of the potentiometer and turns the spindle which changes the resistance. The variation of resistance is linearly proportion to the degree of rotation. Potentiometer, in electronic parlance, is a manually variable resistance. Because its most common consumer application is for controlling volume/tone of sound in broadcast receivers, it is loosely referred to as "volume" or ''tone''. It is not a meter with scale and needle. Potentiometers look different depending on size, power handled, application, value and type of material used. There is, however, a common feature-there is wiper which sweeps over a length of resistive material. The two ends of the resistive material as also the wiper are available to the user as electrical terminations. The user gets a variable resistance between the wiper and the two ends. Also check pack of 5, 16mm size, 22K ohm rotary potentiometers available on Iotcart. These potentiometers have a tolerance of 20% and a total rotational angle of 300° ± 5°. They are described as carbon track, single-turn, adjustable resistances with a plastic shaft. Package Includes: 5 x 47K ohm 16mm Rotatory Variable Potentiometer Specifications: Resistance (Ω)  47k Total rotational angle 300° ± 5° Withstand voltage for 1 minute or more at AC 500V Total resistance tolerance ± 20% (more than 1MΏ ± 30%) Length 16mm

5K ohm 16mm Rotatory Variable Potentiometer Potentiometers are very useful in changing the electrical parameters of a system. It is a single turn 1K Potentiometer with a rotating knob. These potentiometers are also commonly called as a rotary potentiometer or just POT in short.  A potentiometer knob can also be used along with this POT for aesthetic purposes. This is a carbon track, single turn, adjustable resistances, of value 1KOhm Knob potentiometer. It is meant for mounting on panel and is supplied complete with a knob. The knob is affixed on the plastic spindle of the potentiometer and turns the spindle which changes the resistance. The variation of resistance is linearly proportion to the degree of rotation. Potentiometer, in electronic parlance, is a manually variable resistance. Because its most common consumer application is for controlling volume/tone of sound in broadcast receivers, it is loosely referred to as "volume" or ''tone''. It is not a meter with scale and needle. Potentiometers look different depending on size, power handled, application, value and type of material used. There is, however, a common feature-there is wiper which sweeps over a length of resistive material. The two ends of the resistive material as also the wiper are available to the user as electrical terminations. The user gets a variable resistance between the wiper and the two ends. Package Includes: 5 x 5K ohm 16mm Rotatory Variable Potentiometer Specifications: Resistance (Ω)  5k Total rotational angle 300° ± 5° Withstand voltage for 1 minute or more at AC 500V Total resistance tolerance ± 20% (more than 1MΏ ± 30%)

10K Trimpot Trimmer Potentiometer - (Pack of 5) A 10K trimpot (also known as a trimming potentiometer or variable resistor) is a type of adjustable resistor that is commonly used to fine-tune the performance of an electronic circuit. Trimpots are small, usually having a size of about 5 mm to 20 mm in diameter, and are often used in situations where space is limited. A 10K trimpot has a resistance value of 10,000 ohms (10K ohms). Trimpots are classified by their resistance value, which is measured in ohms. A 10K trimpot has a relatively high resistance value compared to some other types of trimpots. A Trimpot or trimmer potentiometer is a small potentiometer that is used for adjustment, tuning, and calibration in circuits. This potentiometer is easy to mount on a PCB and can be adjusted using a screwdriver. What are Potentiometers? A potentiometer is a three-terminal resistor with a sliding or rotating contact that forms an adjustable voltage divider. Package Includes: 5 x 10K Trimpot Trimmer Potentiometer Specifications: Resistance  10K Ohm  Potentiometer Type  Trimpot Tolerance  10% Operating Temperature Range (C) -55 to 125 Mounting Type Through Hole Dimensions(LxWxH) 9.8 x 4.9 x 17.8 mm Weight  10 gm

1K ohm 16mm Rotatory Variable Potentiometer Potentiometers are very useful in changing the electrical parameters of a system. It is a single turn 1K Potentiometer with a rotating knob. These potentiometers are also commonly called as a rotary potentiometer or just POT in short. These three-terminal devices can be used to vary the resistance between 500 to to 1k ohms by simply rotating the knob. A potentiometer knob can also be used along with this POT for aesthetic purposes. This is a carbon track, single turn, adjustable resistances, of value 1KOhm Knob potentiometer. It is meant for mounting on panel and is supplied complete with a knob. The knob is affixed on the plastic spindle of the potentiometer and turns the spindle which changes the resistance. The variation of resistance is linearly proportion to the degree of rotation. Potentiometer, in electronic parlance, is a manually variable resistance. Because its most common consumer application is for controlling volume/tone of sound in broadcast receivers, it is loosely referred to as "volume" or ''tone''. It is not a meter with scale and needle. Potentiometers look different depending on size, power handled, application, value and type of material used. There is, however, a common feature-there is wiper which sweeps over a length of resistive material. The two ends of the resistive material as also the wiper are available to the user as electrical terminations. The user gets a variable resistance between the wiper and the two ends. check out : 10K Pot potentiometer with Knob Package Includes: 5 x 1K ohm 16mm Rotatory Variable Potentiometer Specifications: Resistance (Ω)  1k Total rotational angle 300° ± 5° Withstand voltage for 1 minute or more at AC 500V Total resistance tolerance ± 20% (more than 1MΏ ± 30%)

5250K ohm 16mm Rotary Pot Variable Potentiometer Potentiometers are very useful in changing the electrical parameters of a system. It is a single turn 1M Potentiometer with a rotating knob. These potentiometers are also commonly called as a rotary potentiometer or just POT in short.  A potentiometer knob can also be used along with this POT for aesthetic purposes. This is a carbon track, single turn, adjustable resistances, of value 1M Ohm Knob potentiometer. It is meant for mounting on panel and is supplied complete with a knob. The knob is affixed on the plastic spindle of the potentiometer and turns the spindle which changes the resistance. The variation of resistance is linearly proportion to the degree of rotation. Potentiometer, in electronic parlance, is a manually variable resistance. Because its most common consumer application is for controlling volume/tone of sound in broadcast receivers, it is loosely referred to as "volume" or ''tone''. It is not a meter with scale and needle. Potentiometers look different depending on size, power handled, application, value and type of material used. There is, however, a common feature-there is wiper which sweeps over a length of resistive material. The two ends of the resistive material as also the wiper are available to the user as electrical terminations. The user gets a variable resistance between the wiper and the two ends. Also check 16mm size 470k ohm rotary potentiometer, sold in a pack of 5 by Iotcart. The potentiometer has a tolerance of 20% and is designed for adjusting various parameters like voltage and current in electronic circuits. It is a carbon track, single-turn, adjustable resistor with a plastic shaft. Package Includes: 5 x 1Mohm 16mm Rotary Pot Variable Potentiometer Specifications: Resistance (Ω) 1m Total rotational angle 300° ± 5° Withstand voltage for 1 minute or more at AC 500V Total resistance tolerance ± 20% (more than 1MΏ ± 30%) Length 16mm

5250K ohm 16mm Rotary Pot Variable Potentiometer Potentiometers are very useful in changing the electrical parameters of a system. It is a single turn 250K Potentiometer with a rotating knob. These potentiometers are also commonly called as a rotary potentiometer or just POT in short.  A potentiometer knob can also be used along with this POT for aesthetic purposes. This is a carbon track, single turn, adjustable resistances, of value 250KOhm Knob potentiometer. It is meant for mounting on panel and is supplied complete with a knob. The knob is affixed on the plastic spindle of the potentiometer and turns the spindle which changes the resistance. The variation of resistance is linearly proportion to the degree of rotation. Potentiometer, in electronic parlance, is a manually variable resistance. Because its most common consumer application is for controlling volume/tone of sound in broadcast receivers, it is loosely referred to as "volume" or ''tone''. It is not a meter with scale and needle. Potentiometers look different depending on size, power handled, application, value and type of material used. There is, however, a common feature-there is wiper which sweeps over a length of resistive material. The two ends of the resistive material as also the wiper are available to the user as electrical terminations. The user gets a variable resistance between the wiper and the two ends. Also check pack of 5 16mm rotary potentiometers with a resistance of 1M ohms. These potentiometers have a tolerance of 20% and are used for adjusting various parameters like voltage and current in electronic circuits. The package includes 5 potentiometers, and each has a total rotational angle of 300° ± 5°. Package Includes: 5 x 250K ohm 16mm Rotary Pot Variable Potentiometer Specifications: Resistance (Ω) 250k Total rotational angle 300° ± 5° Withstand voltage for 1 minute or more at AC 500V Total resistance tolerance ± 20% (more than 1MΏ ± 30%) Length 16mm

1K Pot Potentiometer - (Pack of 5) The 1K Pot Potentiometer is a three-terminal variable resistor that is used to vary or change the resistance. It is normally used to control any device. The 10K Potentiometer is used for adjusting various parameters like voltage, current, etc in an electronic circuit. The 1K POT Potentiometer is a passive electronic component that has two end terminals with a resistive element and the sliding contact called the wiper acts as the third terminal. It is mostly used in applications where a single turn can provide enough control resolution. Applications of 1K Potentiometer: DIY kits. Major projects. Mini projects. Audio control. Television control. Motion control. Computation. What are Potentiometers? A potentiometer is a three-terminal resistor with a sliding or rotating contact that forms an adjustable voltage divider. Also check 100K potentiometer in a pack of five. The 100K potentiometer is a three-terminal variable resistor that is used to control various parameters in an electronic circuit. It is commonly used in DIY kits, major projects, mini projects, audio control, television control, and motion control. Package Includes: 5 x 1K Pot Potentiometer Specifications: Resistance  1K Ohm  Potentiometer Type  Pot Potentiometer  Material Carbon Film and Metal Interface 3 Pin Shaft Length 15mm Dimensions  1 x 1 x 1cms  Weight  15 grams

10K ohm 16mm Rotatory Variable Potentiometer Potentiometers are very useful in changing the electrical parameters of a system. It is a single turn 1K Potentiometer with a rotating knob. These potentiometers are also commonly called as a rotary potentiometer or just POT in short.  A potentiometer knob can also be used along with this POT for aesthetic purposes. This is a carbon track, single turn, adjustable resistances, of value 10KOhm Knob potentiometer. It is meant for mounting on panel and is supplied complete with a knob. The knob is affixed on the plastic spindle of the potentiometer and turns the spindle which changes the resistance. The variation of resistance is linearly proportion to the degree of rotation. Potentiometer, in electronic parlance, is a manually variable resistance. Because its most common consumer application is for controlling volume/tone of sound in broadcast receivers, it is loosely referred to as "volume" or ''tone''. It is not a meter with scale and needle. Potentiometers look different depending on size, power handled, application, value and type of material used. There is, however, a common feature-there is wiper which sweeps over a length of resistive material. The two ends of the resistive material as also the wiper are available to the user as electrical terminations. The user gets a variable resistance between the wiper and the two ends. Package Includes: 5 x 10K ohm 16mm Rotatory Variable Potentiometer Specifications: Resistance (Ω)  10k Total rotational angle 300° ± 5° Withstand voltage for 1 minute or more at AC 500V Total resistance tolerance ± 20% (more than 1MΏ ± 30%)

100K Trimpot Trimmer Potentiometer - (Pack of 5) A Trimpot or trimmer potentiometer is a small potentiometer that is used for adjustment, tuning, and calibration in circuits. This potentiometer is easy to mount on a PCB and can be adjusted using a screwdriver. What are Potentiometers? A potentiometer is a three-terminal resistor with a sliding or rotating contact that forms an adjustable voltage divider. Package Includes: 5 x 100K Trimpot Trimmer Potentiometer Specifications: Resistance  100K Ohm  Potentiometer Type  Trimpot Tolerance  10% Operating Temperature Range (C) -55 to 125 Mounting Type Through Hole Dimensions 9.8 x 4.9 x 17.8 mm Weight  10 gm

470K ohm 16mm Rotary Pot Variable Potentiometer Potentiometers are very useful in changing the electrical parameters of a system. It is a single turn 470K Potentiometer with a rotating knob. These potentiometers are also commonly called as a rotary potentiometer or just POT in short.  A potentiometer knob can also be used along with this POT for aesthetic purposes. This is a carbon track, single turn, adjustable resistances, of value 470KOhm Knob potentiometer. It is meant for mounting on panel and is supplied complete with a knob. The knob is affixed on the plastic spindle of the potentiometer and turns the spindle which changes the resistance. The variation of resistance is linearly proportion to the degree of rotation. Potentiometer, in electronic parlance, is a manually variable resistance. Because its most common consumer application is for controlling volume/tone of sound in broadcast receivers, it is loosely referred to as "volume" or ''tone''. It is not a meter with scale and needle. Potentiometers look different depending on size, power handled, application, value and type of material used. There is, however, a common feature-there is wiper which sweeps over a length of resistive material. The two ends of the resistive material as also the wiper are available to the user as electrical terminations. The user gets a variable resistance between the wiper and the two ends. Also check 16mm size 250K ohm rotary potentiometer (plastic shaft) sold by Iotcart. It has a tolerance of 20%. The potentiometer is designed for adjusting various parameters like voltage and current in electronic circuits.  Package Includes: 5 x 470K ohm 16mm Rotary Pot Variable Potentiometer Specifications: Resistance (Ω) 470k Total rotational angle 300° ± 5° Withstand voltage for 1 minute or more at AC 500V Total resistance tolerance ± 20% (more than 1MΏ ± 30%) Length 16mm

Potentiometer Knobs - (Pack of 10) This is a great looking rubberized knob for the potentiometer. Slides onto the potentiometer and holds tightly with a strong friction fit. Package Includes: 10 x Potentiometer Knobs Specifications: Used for  Potentiometers  Material  Abs Plastic Diameter  15mm Dimensions  1.5 x 1.5(inch) Weight  5 grams