170 Points Mini Breadboard

Female to Female Jumper Wires (20cm) 40pcs These are 20cm 40pcs Female to Female Jumper wires, very Flexible and easily detachable. These jumper cables have 1Pin female to the 1pin female header with both ends. Also, it is compatible with 2.54 mm mil spacing pin headers. This cable is an electrical wire or group of them in a cable with a connector or pins at each end, which is normally for interconnecting the components of a breadboard or other prototype or test circuit, internally or with other equipment or components, without soldering. Individual Dupont Cables are fitted by inserting their end connectors into the slots provided in a breadboard, the header connector of a circuit board, or a piece of test equipment. Mostly Dupont cables are useful with Orange Pi, Banana Pi, Raspberry Pi , Arduino , and other mini PCs and development boards . It is very useful in the PCB project, PC motherboard, as well as Breadboard connections. Additionally, these jumper wires allows you to plug and unplug easily for prototyping and can be used over and over again. Check out the best selection of Jumper Wires . Applications: Raspberry Pi Arduino PCB projects Breadboard connections Get a complete set of M2M, M2F, F2F Jumper Wires Set for DIY projects.

A3967 Stepper Motor Driver This A3967 Stepper Motor Driver For Arduino is the most recent version of EasyDriver v44, which was created in collaboration with Brian Schmalz. When compared to previous versions, it offers more flexibility and control over your stepper motor . It is a simple stepper motor driver that is compatible with most microcontrollers and capable of producing a digital 0 to 5V pulse (0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver). A 7V to 30V power supply is required for the module's motor. The digital interface is powered by an onboard voltage regulator that can be set to 5V or 3.3V. The A3967 is a full-featured microstepping motor driver with an integrated transistor. It is intended for use with bipolar stepper motors in full-, half-, quarter-, and eighth-step modes, with output drive capabilities of 30 V and 750 mA. The A3967 comes with a fixed off-time current regulator that can operate in slow, fast, or mixed current-decay modes. This current-decay control scheme produces less audible motor noise, higher step accuracy, and lower power dissipation. The transistor is essential to the A3967's simple implementation. Simply sending one pulse to the STEP input causes the motor to move one step (full, half, quarter, or eighth depending on two logic inputs). It is not necessary to programme phase-sequence tables, high-frequency control lines, or complex interfaces. The A3967 interface is ideal for applications where a complex P is either unavailable or overburdened. Features: A3967 microstepping driver Adjustable current control from 150mA/phase to 750mA/phase MS1 and MS2 pins are broken out to change microstepping resolution to full, half, quarter and eighth steps (defaults to eighth) Compatible with 4, 6, and 8-wire stepper motors of any voltage Breadboard-compatible pins.

CNC Shield for Arduino The CNC shield for Arduino has total four slots, can drive 4 A4988 stepper motors. Each road stepper motors only need two IO ports. In other words, six IO ports can be well managed three stepper motors. The CNC Shield V3.0 allows you to build a engraving machine, 3D printer, mini CNC and other similar devices using your Arduino. It is designed as a shield and can plug on top of an Arduino requiring no external connections and wiring. There are 4 slots on the board for plugging in stepper motor drive module which can drive 1 stepper motor each. Controlling each step stepper motor requires only two IO pins on the Arduino. Just insert this Arduino CNC Shield V3.0 onto an Arduino UNO , and install the GRBL firmware, you can then quickly build a DIY CNC engraving machine. This arduino shield is very convenient to use and is suitable for development boards compatible with Arduino. This CNC shield compatible with Arduino is the latest version of the CN shield model (V 3.0). The CNC Shield is GRBL 0.9 compatible and with the help of jumper wires , it is accessible to stepper drivers. Features: Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place. GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals) 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)

CNC Shield + UNO R3 Board compatible with Arduino + 4xDRV8825 Driver Kit Arduino Uno is an open-source microcontroller used by students and hobbyists entering the world of DIY electronics and automation, The Arduino Uno can be used for any application including being the brains of your next DIY 3D printer and/or CNC router The CNC Shield V3.0 allows you to build an engraving machine, 3D printer, mini CNC and other similar devices using your Arduino. It is designed as a shield and can plug on top of an Arduino requiring no external connections and wiring. Along with that, the CNC shield allows you to control up to four stepper motors by mounting on 4 stepper motor drivers, included with this kit The DRV8825 provides an integrated motor driver solution for printers, scanners, and other automated equipment. The device has two H-bridge and is intended to drive a bipolar stepper motor. Features: UNO R3 Board: The main microcontroller board compatible with Arduino. CNC Shield: An expansion board that allows for easy connection and control of stepper motors. 4x DRV8825 Stepper Motor Drivers: High-performance drivers for controlling stepper motors. Micro-Stepping: Supports micro-stepping settings for precise control of stepper motors. GRBL Compatibility: Compatible with GRBL firmware, which is widely used for CNC control. Voltage Range: Operates on 12-36V DC. Heat Sinks: Included for cooling the stepper motor drivers. USB Cable: For connecting the UNO R3 board to a computer. 40-Pin Row Needles: For additional connections. Applications: CNC Machines: Used for controlling stepper motors in CNC milling, engraving, and cutting machines. 3D Printers: Essential for driving stepper motors in 3D printers, ensuring precise layer deposition and movement. Laser Cutters: Controls stepper motors in laser cutting machines for accurate cutting and engraving. Robotics: Ideal for robotics projects requiring precise motor control, such as robotic arms and automated guided vehicles (AGVs). X-Y Tables: Used in X-Y tables for accurate positioning and movement in various industrial applications. Pick-and-Place Devices: Employed in pick-and-place machines for accurate component placement in electronics manufacturing. Labeling Machines: Used in labeling machines for precise label application. Pinout Diagram for the Arduino Uno Microcontroller Applications of the Kit The kit can be used to create custom 3D printers, scanner, CNC mills and other automated equipment applications

Cytron Maker Pi RP2040 – Robotics Controller Board with Raspberry Pi The Cytron Maker Pi RP2040 is a compact, beginner-friendly robotics controller board powered by the Raspberry Pi RP2040 microcontroller. Designed for DIY robotics, automation, and motion-control projects, this board integrates a dual-channel DC motor driver, four servo ports, and seven Grove connectors - giving makers everything they need to build robots without complex wiring. With compatibility across CircuitPython, MicroPython, C/C++, and even the Arduino ecosystem, this board ranks among the best RP2040 robotics controllers for students, hobbyists, and educators. Built for convenience, the Maker Pi RP2040 supports multiple power input options (USB, LiPo battery, or VIN), includes onboard functional test buttons, and features status LEDs for easy debugging. The preloaded demo code lets you start controlling motors, playing melodies, and testing GPIOs right out of the box. Whether you are exploring Raspberry Pi’s RP2040 ecosystem or building an advanced robot, the Cytron Maker Pi RP2040 robot controller offers exceptional versatility, ease of use, and reliable motor-driving performance. Features: Powered by the Raspberry Pi RP2040 dual-core Arm Cortex-M0+ processor. Includes dual-channel DC motor driver and four servo motor ports for robotics. Seven Grove ports support digital, analog, I2C, SPI, and UART expansion. Preloaded with CircuitPython for easy plug-and-play coding. Supports USB 5V, LiPo 1-cell battery, or 3.6–6V VIN input with automatic switching. Built-in LiPo charging circuit with safety protections. Onboard piezo buzzer, RGB LEDs, GPIO test LEDs, and push buttons. Quick-test buttons and motor output LEDs for immediate motor testing. Fully compatible with the Raspberry Pi Pico ecosystem, MicroPython, C/C++, and Arduino cores. Includes LEGO-compatible mounting holes and M3 mounting points. Board Layout: Dimension:

SmartElex Micro ISM330DHCX 6DoF IMU Sensor The SmartElex Micro ISM330DHCX 6DoF IMU Sensor is a compact motion-sensing module that combines an accelerometer and gyroscope to measure movement, orientation, and rotation. It helps users track motion data accurately in three-dimensional space, making it useful for students, hobbyists, engineers, and educators working on robotics, automation, and motion-based electronics. This IMU breakout board simplifies motion tracking in projects where stability, responsiveness, and precision are important, without requiring complex circuit design or calibration setups. This 6DoF IMU sensor is commonly used in self-balancing robots, gesture-controlled systems, IoT wearables, drones, and embedded automation projects that rely on movement or orientation feedback. It integrates smoothly with popular development platforms like Arduino, Raspberry Pi, and ESP32, making setup and data processing beginner-friendly and efficient. With dependable performance and straightforward compatibility, the SmartElex Micro ISM330DHCX is a practical choice for prototyping, academic learning, and product development where reliable motion tracking and sensor fusion are essential. Features: 6DoF IMU with built-in accelerometer and gyroscope for motion tracking Measures linear acceleration and rotational movement in real time Compact breakout board designed for easy integration in projects Compatible with Arduino, Raspberry Pi, ESP32, and similar platforms Ideal for robotics, drones, wearables, and gesture-based control systems Reliable module for prototyping, STEM learning, and embedded development

Cytron URC10 Sumo Robot Controller R1.1 Arduino-Compatible Motor Driver Board The Cytron URC10 Sumo Robot Controller R1.1 is a powerful all-in-one robotics control board designed specifically for competitive sumo robot building. It combines an Arduino-compatible ATmega328P microcontroller, a dual 10A motor driver, and dedicated interfaces for ultrasonic, digital, and analog sensors - making it one of the most efficient and beginner-friendly solutions for robot builders. With support for 8V–25V DC motors, 30A peak current, and high-frequency PWM control, this controller ensures strong pushing power and fast maneuverability for 3kg sumo robot competitions. Cytron engineered the URC10 to simplify robot development by integrating essential hardware like built-in test buttons, motor output LEDs, onboard 5V/3.3V regulators, and a Micro-USB interface for programming. Whether you're designing autonomous systems, competitive sumo robots, or experimenting with robotics, the Cytron URC10 offers reliable performance, stable motor control, and easy sensor expansion for both beginners and advanced makers. Features: Designed specifically for up to 3kg sumo robot applications. Built around the Arduino-compatible ATmega328P microcontroller with Optiboot Bootloader. Integrated dual 10A continuous motor driver (30A peak per channel) for high-power brushed DC motors. Supports 8V–25V motor voltage for a wide range of robot motors. Features current limiting at 30A per channel for safe operation under heavy loads. Includes motor test buttons for quick verification without uploading code. Motor output status LEDs for easier debugging and inspection. Compatible with sign-magnitude and locked-antiphase PWM, supporting up to 20kHz frequency. Onboard 5V, 1A regulator and 3.3V, 500mA regulator for powering sensors and modules. Dedicated pins for motors, ultrasonic sensors, digital I/O, and analog sensors. Includes USB Micro-B + CH340 USB-serial system for easy programming upload. Provides 1× I2C port for additional modules. Compact design with dimensions 75.57mm × 99.7mm. Note: Reverse polarity protection is not included.

7Semi MCP4728 Quad DAC Module The 7Semi MCP4728 Quad DAC Module is a compact and reliable DAC module designed to convert digital signals into precise analog voltage outputs. Based on the MCP4728 IC, this digital-to-analog converter breakout board allows users to generate up to four independent analog outputs using simple I²C communication, making it an efficient solution for applications where microcontrollers lack sufficient analog output pins or require higher accuracy. This module offers easy integration with popular microcontrollers, stable performance, and flexible voltage output control, making it ideal for signal generation, sensor simulation, audio control, and calibration tasks. With its user-friendly design and dependable operation, it is well suited for students learning embedded systems, hobbyists building DIY electronics, and professionals developing prototypes or compact analog control systems. Features: Powered by the Microchip MCP4728 Quad DAC IC 12-bit resolution on all four DAC output channels (A–D) Onboard non-volatile EEPROM retains DAC settings after power-off I²C interface with Fast Mode support up to 400 kHz Low-power operation, ideal for battery-powered projects Compact 7Semi breakout with clearly labeled pinouts Supports LDAC and RDY pins for real-time DAC updates and monitoring Applications: Signal generation (sine, square, and triangle waveforms) Audio voltage control for synthesizers and mixers Programmable and adjustable reference voltage sources Lab instruments, testing, and control systems Industrial automation and process control applications Multi-channel analog and neural interface testing

SmartElex 12V 7A Single Channel Power Relay Module The SmartElex 12V 7A Single Channel Power Relay Module is a dependable switching solution designed to control higher-power electrical loads using low-voltage control signals. It helps protect microcontrollers and sensitive electronics by providing proper isolation between the control circuit and the load side. This module is suitable for students, makers, engineers, educators, and startups who are working on control systems, automation projects, or embedded applications that require safe and reliable power switching. This single channel power relay module is ideal for robotics, IoT systems, home automation, and industrial control projects where devices such as motors, lights, pumps, or other electrical equipment need to be switched reliably. It can be easily interfaced with popular development platforms like Arduino, Raspberry Pi, and ESP32, making it convenient for both prototyping and final product integration. The simple design and consistent performance allow users to build stable control systems without added complexity. Features: Single channel power relay module for high-load switching Operates on 12V, suitable for automation and control systems Supports up to 7A load current for power applications Electrical isolation between control side and load side for safety Compatible with Arduino, Raspberry Pi, ESP32, and similar boards Compact and durable design for easy integration into projects

7Semi SGP40 VOC Sensor Breakout for Indoor Air Quality 2.54mm Pitch (ES-12201) The 7Semi SGP40 VOC Sensor Breakout for Indoor Air Quality (ES-12201) is a compact sensor module designed to monitor indoor air quality by detecting volatile organic compounds (VOCs). It uses the reliable Sensirion SGP40 sensor, which helps track changes in air quality and provides useful data for healthier indoor environments. This breakout board features a standard I2C interface and 2.54 mm pitch pins, making it easy to connect with popular microcontrollers like Arduino, ESP32, and Raspberry Pi. Operating at low power and designed for simple integration, it is ideal for air quality monitors, smart home devices, and indoor environmental sensing projects. Features: Uses the Sensirion SGP40 sensor for reliable VOC detection Measures volatile organic compounds (VOCs) to assess indoor air quality I2C digital interface for easy connection with microcontrollers Standard 2.54 mm pitch pins for breadboard and prototyping use Low-power operation suitable for battery-powered and IoT projects Works with Arduino, ESP32, Raspberry Pi, and other development boards

SmartElex Atmospheric Sensor Breakout – BME280 Temperature, Humidity & Pressure Sensor Module The SmartElex Atmospheric Sensor Breakout is a compact and reliable module designed to measure temperature, humidity, and air pressure with high accuracy. Built around the powerful BME280 sensor, this 3-in-1 sensor module makes it easy to monitor environmental conditions in real time. Perfect for weather stations, IoT systems, and smart home devices, this environmental sensor breakout delivers precise readings while consuming very little power. It supports both I2C and SPI communication interfaces, making it simple to connect with popular boards like Arduino, ESP32, or Raspberry Pi. Whether you’re building an automation project or a DIY weather monitor, this temperature, humidity, and pressure sensor breakout provides reliable performance and easy integration. It’s a great choice for makers, students, and developers who want accurate environmental data in a small and efficient module. Features: 3-in-1 Environmental Sensor: Accurately measures temperature, humidity, and barometric pressure using the BME280 sensor. High Precision Readings: Provides stable and accurate data for weather monitoring and environmental analysis. I2C & SPI Compatible: This I2C SPI environmental sensor module easily interfaces with Arduino, ESP32, Raspberry Pi, and other microcontrollers. Compact Design: Small and lightweight, making it perfect for embedded systems, IoT devices, and portable applications. Low Power Consumption: Efficient sensor design ensures reliable long-term use in battery-powered projects. Easy to Integrate: Ideal for beginners and professionals working on DIY weather stations, home automation, or environmental monitoring systems.

7Semi SHT40 Temperature & Humidity Sensor Breakout Board with 1.27mm Pitch The 7Semi SHT40 Temperature and Humidity Sensor Breakout is a compact, precision-engineered module built for applications where accurate environmental monitoring and ultra-low power consumption are crucial. Powered by Sensirion’s fourth-generation SHT40 sensor, it delivers highly reliable 16-bit temperature and humidity data while operating at just 3.3V. With its exceptionally low energy usage, fast response time, and robust ±1.8% RH and ±0.2°C accuracy, it’s an ideal upgrade for modern IoT, wearable, and battery-powered designs that demand consistent and stable performance. Designed for effortless integration, the board features a 1.27 mm pitch, a 4-pin header, and a versatile I2C interface with multiple address options, making it simple to deploy across embedded systems, development platforms, and prototype setups. Whether you're building smart home automation, industrial monitoring, or IoT environmental sensing projects, this SHT40 breakout ensures dependable, long-term operation even in demanding ambient conditions, helping engineers and makers achieve more accurate and energy-efficient data processing. Features: The SHT40 sensor delivers high-precision readings with ±1.8% RH humidity accuracy and ±0.2°C temperature accuracy for trustworthy environmental data. Designed for low-power applications, operating at under 0.15mA in low-power mode for extended battery life. Compact breakout board with a 1.27 mm pitch 4-pin header, making it ideal for tight-space electronic designs and fast prototyping. Provides a reliable I2C communication interface with multiple preconfigured addresses for easy use in multi-sensor networks. Efficient 3.3V operation ensures stable performance across microcontroller and IoT platforms. Fast response time of 8 seconds for real-time temperature and humidity tracking. Suitable for smart homes, industrial automation, IoT environmental nodes, air quality systems, and intelligent building applications.

SmartElex RLS05 Line Follower Sensor The SmartElex RLS05 Line Follower Sensor is a compact and easy-to-use module designed to help robots detect and follow lines on a surface with accuracy. It is ideal for students, makers, educators, and early-stage engineers who are learning robotics or building simple autonomous systems. The sensor simplifies line detection by clearly identifying path contrasts, making it easier to develop reliable line-following behavior without complex circuit design. This sensor is widely used in line follower robots, educational robotics kits, and automation prototypes where precise path tracking is required. It integrates smoothly with popular platforms such as Arduino, Raspberry Pi, and ESP32, allowing quick setup and experimentation. With dependable performance and straightforward interfacing, the SmartElex RLS05 enables users to focus on coding logic and robot movement, making it well suited for classrooms, labs, competitions, and DIY robotics projects in India. Pin Diagram: How to Calibrate SmartElex RLS05 Line Follower Sensor Step 1: Enter Calibration Mode Press the calibration button once or pull the CAL pin low for a few milliseconds. When three LEDs (D0, D2, and D4) turn ON, the module has entered calibration mode. Step 2: White Surface Reading Place the RLS05 module on a white surface and press the calibration button again. When two LEDs (D3 and D4) turn ON, the white surface values are read and saved in EEPROM. Step 3: Black Surface Reading Place the module on a black surface and press the calibration button once more. When three LEDs (D2, D3, and D4) turn ON, the black surface values are read and stored. Step 4: Select Line Following Mode To enable white line following, press the calibration button three times within one second. LEDs (D2, D3, and D4) will blink to confirm selection. To enable black line following, press the calibration button twice. LEDs (D0, D1, and D2) will blink to confirm the mode selection. Features: Five-channel line detection for accurate and stable line following Supports both black line and white line tracking modes One-time calibration with onboard EEPROM memory Easy calibration using onboard push button or CAL pin Compatible with Arduino, Raspberry Pi, and ESP32 platforms Ideal for robotics projects, educational kits, and automation prototypes

SmartElex LHI778 PIR Motion Sensor Module The SmartElex LHI778 PIR Motion Sensor Module is a passive infrared motion detection solution designed to sense human movement by detecting changes in infrared radiation. It helps solve the problem of automatic motion detection without continuous monitoring, making systems more energy efficient and responsive. This module is suitable for students, makers, engineers, educators, and startups working on electronics projects that require reliable motion sensing for control, security, or automation purposes. This PIR motion sensor module is widely used in robotics, IoT devices, security systems, and home or industrial automation projects where movement detection is required. It can be easily interfaced with popular development platforms such as Arduino, Raspberry Pi, and ESP32, allowing quick integration into prototypes and functional systems. The simple interface and consistent performance make it ideal for applications like motion-activated lighting, intrusion detection, smart alarms, and interactive electronic projects. Features: Passive infrared (PIR) sensor for reliable human motion detection Detects movement by sensing changes in infrared radiation Low power operation suitable for battery-powered projects Digital output for easy interfacing with microcontrollers Compatible with Arduino, Raspberry Pi, ESP32, and similar boards Ideal for security systems, automation, and motion-activated applications

ATMEGA328P SMD IC for Arduino Nano/UNO – AVR Microcontroller The ATMEGA328P SMD IC (ATMEGA328P-AU) is a high-performance 8-bit AVR microcontroller widely used in Arduino Nano and Arduino Uno boards. Designed with picoPower technology, this SMD version includes 32KB ISP Flash, 2KB SRAM, 1KB EEPROM, multiple timers, USART, SPI, and I2C support. Making it ideal for embedded electronics, DIY projects, automation systems, and IoT applications. Its compact SMD package makes it suitable for custom PCB designs and small-form-factor projects. This microcontroller is fully compatible with Arduino IDE, making programming easy using an AVR programmer or bootloader. With features like 23 GPIO pins, 6-channel 10-bit ADC, watchdog timer, and flexible power-saving modes, the ATMEGA328P SMD IC delivers powerful performance while maintaining low power consumption. Whether you're building a new Arduino-compatible board or repairing an existing one, this IC provides reliability, stability, and seamless integration. Features: ATMEGA328P-AU SMD AVR microcontroller used in Arduino Nano/UNO boards. Supports 32KB Flash memory with read-while-write capability, 1KB EEPROM, and 2KB SRAM. Fully compatible with Arduino IDE; can be programmed using an AVR programmer. Offers 23 GPIO pins, 3 timers/counters, watchdog timer, and hardware serial communication. Integrated SPI, I2C (TWI), and USART interfaces for seamless connectivity. Operates on 1.8V to 5.5V, suitable for low-power and battery-based projects. 6-channel 10-bit ADC (8-channel in TQFP package) for accurate analog sensing. SMD design ideal for custom PCBs, compact electronics, and embedded projects.