VeroBoard(6x4 Inch)

15cm x 10cm Single Side Copper Clad Laminate PCB Board Ideal for building a prototype of electronic circuit, double sided copper PCB. Mechanically assisted and electrically connects electronic components with conductive rails, pads and other features etched from copper plates on a non-conductive substrate. This product is widely used in product development, DIY experiments, maintenance, production, etc.

Vero Board (2x3 Inch) Vero Board is basically a general-purpose printed circuit board (PCB), also known as veroboard or DOT PCB. It is a thin rigid copper sheet with holes pre-drilled at standard intervals across a grid with 2.54mm (0.1-inch) spacing between holes. Each hole is encircled by a round or square copper pad so that component lead can be inserted into the hole and soldered around the pad without short-circuiting the nearby pads and other leads. For connecting the lead of component with another lead, solder these together or join these using a suitable conducting wire. Application: Hold electronic components Develop prototypes of electronic circuits

555 Timer IC The 555 timer IC is an integrated circuit (chip) used in a variety of timer, pulse generation, and oscillator applications. The ic 555 can be used to provide time delays, as an oscillator, and as a flip-flop element. Derivatives provide up to four timing circuits in one package. These 555 timer ICs are precision timing circuits capable of producing accurate time delays or oscillations. In the time-delay or monostable mode of operation, the timed interval is controlled by a single external resistor and capacitor network. In the astable mode of operation, the frequency and duty cycle can be controlled independently with two external resistors and a single external capacitor. The threshold and trigger levels normally are two-thirds and one-third, respectively, of VCC. These levels can be altered by the use of the control voltage terminal. When the trigger input falls below the trigger level, the flip-flop is set and the output goes high. If the trigger input is above the trigger level and the threshold input is above the threshold level, the flip-flop is reset and the output is low. The reset (RESET) input can override all other inputs and can be used to initiate a new timing cycle. When RESET goes low, the flip-flop is reset and the output goes low. When the output is low, a low-impedance path is provided between discharge (DISCH) and ground. The output circuit is capable of sinking or sourcing current up to 200 mA. The operation is specified for supplies of 5 V to 15 V. With a 5-V supply, output levels are compatible with TTL inputs. The NE555 is characterized for operation from 0°C to 70°C. This is characterized for operation from –40°C to 85°C. The NE555 is characterized for operation over the full military range of –55°C to 125°C. Features of the 555 timers are: Supply voltage between 4.5 and 18 volts. supply current 3 to 6 mA, and a Rise/Fall time of 100 nSec. IC 555 pin diagram The IC 555 is used in many circuits, for example, a One-shot pulse generator in Monostable mode as an Oscillator in Astable Mode or in Bistable mode to produce a flip/flop type action. It is also used in many types of other circuits for the achievement of various purposes for instance Pulse Amplitude Modulation (PAM), Pulse Width Modulation (PWM), etc. This IC 555 can be configured to use as a monostable multivibrator, an astable multivibrator. If you want to use this 555 timer ic in your projects, there are a few essential components that are helpful are breadboard or vero board , switch , jumper wires , resistors , capacitors and batteries . Features: Adjustable Duty Cycle. Precision timing circuits capable of producing accurate time delays or oscillations. Can be configured as a monostable multivibrator, astable multivibrator, or in bistable mode. Features a control voltage terminal to alter threshold and trigger levels. RESET input for initiating a new timing cycle. Rise/Fall time of 100 nSec. Applications: The IC 555 is used for Tone generation. It is used to make an alarm circuit. They are also used for frequency division applications. The IC 555 is used as a relaxation oscillator. They are also used in digital counter circuits. IC 555 is widely used for electronics projects. Also check 8 Pin DIP IC Socket Base Adaptor available on the Iotcart website. it is designed for 8-pin integrated circuits (ICs) commonly used in electronic devices like timers, oscillators, and digital logic circuits. The socket has a molded notch for proper orientation, making it easy to insert and remove ICs

Micro USB Breakout Board Power Charging Module The MCU-Micro USB Breadboard 5V Power Supply Module with a 5-pin female connector B type PCB converter is an excellent tool for connecting USB signals to your microcontroller boards. It also serves as a useful resource if you require access to 5V USB power for your prototype circuits, including breadboards , perforated boards, or Vero boards . Pinout VCC: 5V Power Supply D- : USB D- Signal D+: USB D+ Signal ID: USB Identifier Signal for OTG Devices GND: Power Ground

1660 tie-point Solderless Breadboard The 1660 Points Solderless Breadboard is an excellent size with more than enough room for more advanced prototyping. There are two terminal strips with 1260 tie-points and 4 distribution strips with 400 tie-points. The breadboards accept a variety of wire sizes from 20 to 29 AWG.

170 Points Mini Breadboard This 170 Points Mini Breadboard is the ideal companion for seamless electronics prototyping, designed to provide a hassle-free experience. With a 2x17 row layout and a total of 170 pins, this prototyping breadboard offers abundant space to create and test various circuits and it is crafted with top-notch materials. This solderless breadboard simplifies your prototyping process – no soldering is required. This durable and compact breadboard for DIY electronic projects is beginner-friendly and suited for all skill levels. It's compatible with a wide range of electronic components, including Arduino, Raspberry Pi, sensors, and more. The compact and portable design, measuring 45x35x9mm, ensures it fits seamlessly into your projects. Understanding What is Breadboard and its types. Features: Self-adhesive for convenient use Sturdy build with high-quality materials for durability No soldering is required for quick assembly Compatible with various electronic components like Arduino, Raspberry Pi, sensors, etc. Ideal for hobbyists, students, and professionals Compact design suitable for a wide range of electronics projects Applications: Electronics prototyping for experimenting with circuits Seamless testing and development of electronic projects Suitable for small to medium-sized projects due to its compact design Versatile use in IoT development and automation projects

40x1 Pin 2.54mm Single Row Straight Male Pin Header Strip (Pack of 50) This Single Row 40 Pin Berg Strip Pack of 50. The 50 Quantity Headers can be used in multiple DIY electronic applications. This Male Berg Strip bundle has pitch size of 2.54 Millimeters which can be easily used with any Standard Circuit Board like Vero Boards, Breadboards. This 40 Pin Male Break Away Header Pack of 50 has the industry standard spacing of 2.54mm and are designed for soldering directly into printed circuit boards (PCB). They are best for extension of pins of Microcontrollers and ICs.

GL12 MB102 840 Points Solderless Breadboard Introducing the GL12 840 Points Breadboard at Iotcart! This solderless breadboard is an essential tool for any electronics engineer or hobbyist. It allows you to make temporary prototypes for your electronics projects, making it perfect for experimenting with circuit designs. The GL12 breadboard for projects accepts a variety of wire sizes (20-29 AWG) and is completely reusable with its self-adhesive back. This durable & compact prototyping breadboard is compatible with various electronic components, including resistors, diodes, transistors, LEDs, and capacitors. You can easily modify or revise circuits, making it a versatile and convenient choice. This solderless breadboard comes with 840 tie points and 128 groups of 5 connected terminals, along with 8 buses of 25 connected terminals. No soldering is required, making it effortless to change connections and replace components. Plus, the tight fit for ICs and wires, labeled power rails, and sturdy ABS material ensure a smooth and efficient prototyping experience. Read more: What is Bread Board - Applications, Types & Working Key Features: Accepts wire sizes from 20 to 29 AWG. Easy circuit modifications without soldering. 840 tie points for connections. 128 groups of 5 connected terminals and 8 buses of 25 connected terminals. Reusable with a self-adhesive back. Compatible with various electronic components. Tight fit for integrated circuits (ICs) and wires. Solderless design for easy connection changes. Applications: Hold electronic components Develop prototypes of electronic circuits Educational Projects DIY electronics projects

40x1 Pin 2.54mm Straight Female Pin Berg Strip (Pack of 50) This is a 40 Pin single row straight female berg strip 50 Quantity. These 50 Quantity Female header pin comes with universally standard spacing of 2.54 Millimeters. The 40 Pin 2.54mm Pin Headers for PCB boards can be easily used with Arduino Uno, Arduino Shields, Node MCU, and other Circuit boards. High Quality, Gold-Plated Contact, better electrical conductivity and low contact resistance. Generally used in circuit boards and other low-voltage circuits. This pin header is a ideal socket connector for the PCB board and integrated circuit, is used widely in the Vero board and breadboard.

Vero board (3x4 Inch) Veroboard is a brand of stripboard, a pre-formed circuit board material of copper strips on an insulating bonded paper board which was originated and developed in the early 1960s. VeroBoard is a new type of surface mount technology(SMT) and integrated circuit (IC) prototyping platform. A new tooling technique and advanced manufacturing process, VeroBoard can be a great alternative to traditional prototyping boards. VeroBoard is the smallest lead-free surface mount technology platform in the world. VeroBoard is the best zero PCB board and is widely applied in the fields of PCB Designing. The Zero pcb board price varies based on its size. One can buy the Vero Board from Iotcart at a very Low Price. check out : Vero Board (2x3 inch)? Features: Pre-formed circuit board for electronic prototyping Surface Mount Technology (SMT) and integrated circuit (IC) prototyping platform Advanced manufacturing process for lead-free technology Single side copper PCB Referencing numbers printed on four sides for easy reference of individual holes Applications: Electronic circuit prototyping Development of surface mount technology (SMT) projects Integrated circuit (IC) prototyping DIY electronics projects Creating custom electronic modules Testing and validating circuit designs before PCB fabrication Rapid prototyping for small-scale electronic projects

PCB Toner Transfer Paper A4 Size for DIY Electronics This PCB Toner Transfer Paper A4 Size is specially designed for DIY electronics enthusiasts looking to fabricate custom PCBs at home. Using this high-quality toner transfer paper, you can easily transfer your PCB artwork onto a blank copper-clad board with the help of a laser printer and heat, either from an iron or a lamination machine. The process is simple and efficient, making PCB prototyping fast and budget friendly. Once the artwork is transferred, you can etch the board using Ferric Chloride to reveal your final PCB design. Whether you're a hobbyist, student, or electronics maker, this toner transfer paper is an essential tool for creating your own printed circuit boards. Features: A4-size sheet compatible with most laser printers Special coating ensures crisp and clear toner transfer Fast thermal transfer using an iron or a laminator Enables precise PCB artwork reproduction Ideal for single or double-sided PCB prototyping

PCB Toner Transfer Paper A4 Size for DIY Electronics This PCB Toner Transfer Paper A4 Size is specially designed for DIY electronics enthusiasts looking to fabricate custom PCBs at home. Using this high-quality toner transfer paper, you can easily transfer your PCB artwork onto a blank copper-clad board with the help of a laser printer and heat, either from an iron or a lamination machine. The process is simple and efficient, making PCB prototyping fast and budget friendly. Once the artwork is transferred, you can etch the board using Ferric Chloride to reveal your final PCB design. Whether you're a hobbyist, student, or electronics maker, this toner transfer paper is an essential tool for creating your own printed circuit boards. Features: A4-size sheet compatible with most laser printers Special coating ensures crisp and clear toner transfer Fast thermal transfer using an iron or a laminator Enables precise PCB artwork reproduction Ideal for single or double-sided PCB prototyping

Full Stack IoT Lab Development IoTIF IoT Kit X 10 ESP 32 Module With Cable X 10 Tiny ML Kit X 5 Extra Sensor 37 in 1 Sensor Kit X 10 Extra Actuators 3.5 Inch Raspberry Pi Display X 5 5 Inch Raspberry Pi Display X 5 Wireless Lora Gateway X 1 Lora Bee Modules X 10 NEO 6M GPS X 10 4G GPS SIM7670C X 5 Xbee Module S2C Pro with Base X 5 HM 10 Low Energy X 5 RFID RC522 X 10 RFID Micro USB X 5 HC12 X 10 RF433 MHZ X 10 Mech 2WD Kit X 10 4WD Kit X 10 Gear Motor X 10 Bo Motor X 10 Toy Motor X 10 3D Printer X 1 Smart Home 4 CH. Relay Module X 10 Bulb Holder X 10 Bulb X 10 AC Wire Set X 10 2 Pin Plug X 10 Measurement Instruments Soldering Station X 5 Lead X 5 Soldering Wires X 5 Cutter X 5 Nipper X 5 Desoldering Pump X 5 Oscilloscope X 2 Dual Supply X 2 Mastech Multimeter X 10 Clamp Meter X 5 Glue Gum 40 watt X 5 Glue Stick X 100 Signal Generator X 2 12V 1 Amp Power Adapter X 5 12V 2 Amp Power Adapter X 5 5V 1 Amp Power Adapter X 5 5V 2 Amp Power Adapter X 5 Components and Wires Breadboard X 10 Half Breadboard X 10 Resistance Box X 10 Capacitor Box X 10 Transistor Box X 10 Diode Box X 10 Switch Box X 10 Vero Board Multiple size X 10 Jumper wires (M2M, M2F, M2F) X 10 Drone Kit Complete DIY Drone Kit X 2 Camera Raspberry Pi Official Camera X 10 IoT Platform and Software Kicad X 10 Fritzing X 10 Qucs X 10 Scilab X 10 Thingsboard.io X 10 Firebase Cloud X 10 Thinger.io X 10 IIOTIF X 10 Training and FDP Offline Training (2 Days) X 1 Online Training (100 Hours) X 1

SYB-500 Large Solderless Breadboard – 3220 Tie-Point Prototyping Board (240×200×8.5mm) The SYB-500 Large Breadboard is a high-capacity solderless prototyping board designed for advanced electronics development, circuit testing, and educational experimentation. With its spacious layout and durable construction, this board provides an efficient platform for building complex circuits without soldering. The generous 240mm × 200mm × 8.5mm size ensures ample working space for ICs, sensors, modules, and jumper wires, making it ideal for students, hobbyists, and professionals. Built with high-quality materials and reliable nickel-plated contacts, the SYB-500 ensures stable connections for a wide range of electronic components. As part of a professionally distributed product range, it maintains consistent performance suitable for engineering labs, robotics projects, embedded system development, and industrial testing environments. Whether you're building prototypes or learning circuit design, this breadboard offers exceptional flexibility and longevity. Features: Large solderless breadboard with a spacious working area. Dimensions: 240mm × 200mm × 8.5mm for complex circuit layouts. Strong plastic base with nickel-plated contacts for stable, corrosion-resistant connectivity. Supports ICs, sensors, microcontroller modules, and discrete components. Ideal for engineering labs, robotics, prototyping, and educational projects. Reusable and easy to modify without soldering. High reliability backed by professional component distribution standards.